- How much does a gallon of Thompson’s Water Seal cover?
- What temperature do you apply Thompson’s Water Seal?
- Is it better to seal or stain a deck?
- What is the best waterproof sealer for wood?
- What is the best way to apply Thompson’s Water Seal?
- Is Thompson Water Seal oil or water based?
- How long does Thompson’s Water Seal last?
- How often does Thompson’s Water Seal need to be applied?
- Can you mix Thompson’s Water Seal with stain?
- Is Thompson’s Water Seal any good?
- How many coats does Thompson’s Water Seal have?
- What happens if it rains after applying Thompson’s Water Seal?
How much does a gallon of Thompson’s Water Seal cover?
That determines how many gallons of stain are required (each gallon covers up to 400 square feet)..
What temperature do you apply Thompson’s Water Seal?
Be sure that both surface and air temperatures are above 50°F during application and remain above 40°F for 48 hours after application. Do not apply product if rain is forecasted within 24 hours of application. Perform the splash test. Sprinkle water on various sections of surface to be sealed.
Is it better to seal or stain a deck?
A: It’s really up to you. Just staining the deck will give you the color you want, although in high-traffic areas the stain could wear away quickly. … The advantage of this, they say, is the sealer provides additional protection against water and weather damage, while the stain helps reduce fading from UV rays.
What is the best waterproof sealer for wood?
Our Top PicksBEST OVERALL: SEAL-ONCE MARINE Penetrating Wood Sealer. … EASIEST APPLICATION: Eco Advance Exterior Wood Water Repellent. … BEST VALUE: Olympic Stain Smartguard Concentrated Sealant. … LONGEST-LASTING SEAL: Olympic Stain Maximum Waterproofing Sealant.
What is the best way to apply Thompson’s Water Seal?
Surfaces must be thoroughly cleaned prior to application with a deck cleaner (like those in the Thompson’s® WaterSeal® cleaner line) applied according to label directions and cautions. If surface is damp or wet from cleaning or weather, allow the surface to dry thoroughly (a minimum of 48 hours) before application.
Is Thompson Water Seal oil or water based?
Thompson’s® WaterSeal® Penetrating Timber Oil is an oil-based product that provides protection by penetrating into wood pores and sealing out water infiltration. Thompson’s® WaterSeal® Waterproofing Stains are water-based products that have film-forming properties to protect the wood by repelling water.
How long does Thompson’s Water Seal last?
10 yearsIf applied correctly, Water Seal will last up to 10 years.
How often does Thompson’s Water Seal need to be applied?
every one to three yearsApplying a sealer and/or stain typically is recommended every one to three years, depending on the finishing product, deck use, weather conditions, and sun exposure. All Thompson’s WaterSeal products are DIY-friendly, and most need only a single application on a clean, dry deck.
Can you mix Thompson’s Water Seal with stain?
As long as it’s all oil based you should be able too. But if it’s a solid color stain it might turn a little transparent if mixed with the sealer…..just give it a try on a scrap piece. Bingo. As long as they use the same solvents, it should be fine.
Is Thompson’s Water Seal any good?
5.0 out of 5 stars Love Thompson’s Water Seal with the harvest gold color! Basically, it takes your weather worn fence and restores it back to almost new looking boards, plus protecting it from the elements. I used my spray gun to apply, and a little goes a long way. Obviously, you can use a brush to apply it as well.
How many coats does Thompson’s Water Seal have?
Thompson’s WaterSeal Waterproofing Stains. Application: Only one coat is recommended for both Semi –Transparent & Solid. A second coat can be added if more color is desired. Allow the first coat to dry (approximately 2 hours) before second application.
What happens if it rains after applying Thompson’s Water Seal?
Rain will damage the finish of any wet sealer with linseed oil or mineral oil in it. Because it forms a coating, it takes several hours to “set up” (dry) and during that time the sealer is vulnerable.